Concrete Block Calculator

%
in
$
$
$
$
$
$

Block Wall Preview

189 Blocks Needed
14 Mortar Bags
0.04 t Sand
120 ft Reinforcement

Core Fill

Grout
75 Bags

Estimated Cost

$472.50 Blocks
$168.00 Mortar
$1.47 Sand
$72.00 Reinforcement
$713.97 Total

How the Calculator Works

Concrete block quantity depends on the wall's total area and the face area of a single block. Dividing wall area by block face area gives the raw block count, and adding a waste allowance covers cuts and breakage.

Blocks = (Wall Length × Wall Height) ÷ Block Face Area

Block face area is based on the standard 8in by 16in face size, adjusted for the mortar joint thickness you enter. The calculator also estimates mortar bags, sand, and horizontal reinforcement, and can estimate grout or vermiculite fill if you plan to fill the block cores.

Why Manual Estimates Go Wrong

Most concrete block estimates go wrong in one of two ways.

Mistake #1: Using nominal block size without accounting for the joint

A standard block is manufactured slightly under 8 by 16 inches so that, once mortar joints are added, the installed module comes out to a clean 8 by 16 inches. Using a different assumed joint thickness changes how many blocks actually fit per square foot of wall.

Mistake #2: Forgetting reinforcement and fill materials

A block count alone does not cover a complete wall. Horizontal joint reinforcement is standard in most block walls, and any wall with cells filled with grout or vermiculite needs that volume calculated separately from the block and mortar count.

Concrete Block Sizes and Coverage

These are standard concrete block thicknesses and their typical grout fill volume per 100 square feet of wall, when cells are fully filled.

Thickness Face Size Grout Fill per 100 sq ft Common Use
6 in8 x 16 in0.93 yd³Non-load-bearing partitions
8 in8 x 16 in1.12 yd³Standard load-bearing walls
12 in8 x 16 in1.65 yd³Foundations, retaining walls

Example: A 20-foot by 8-foot wall built with standard 8in blocks and a 3/8in mortar joint needs about 189 blocks with a 5% waste allowance, roughly 14 bags of mortar, and about 120 feet of horizontal reinforcement at 16in spacing.

Choosing Block Thickness and Reinforcement Spacing

Block Thickness

6in block suits non-load-bearing interior partitions. 8in is the standard choice for most load-bearing exterior and foundation walls. 12in is used for taller retaining walls or where local code requires greater load capacity.

Reinforcement Spacing

16in on center is the more common spacing and provides more frequent reinforcement courses. 24in on center uses less material but is only appropriate where local code and engineering requirements allow the wider spacing.

Frequently Asked Questions

Multiply the wall's length by its height to get the total area, then divide by the face area of a single block, which is about 0.89 square feet including a standard 3/8in mortar joint. Round up and add a waste allowance, typically 5 to 10 percent, to cover cuts and breakage.
A common industry rule of thumb is about 7 bags of masonry cement per 100 blocks. Actual usage varies with joint thickness, block dimensions, and workmanship, so this figure is best treated as a planning estimate rather than an exact quantity.
The standard concrete masonry unit has an 8 by 16 inch face, with the actual manufactured block slightly smaller so the installed size reaches exactly 8 by 16 inches once mortar joints are added. Thickness (the block's depth into the wall) commonly comes in 6, 8, and 12 inch options.
Not always. Filling cores with grout is typically required only where structural engineering or local code calls for it, often at reinforced cells or for taller and load-bearing walls. Lightweight vermiculite fill is sometimes used instead for insulation purposes rather than structural reinforcement.
Concrete blocks are typically 8 by 16 inches and used for structural walls and foundations, while clay bricks are much smaller, roughly 2.25 by 3.75 by 8 inches, and often used for facing rather than structural walls. The two materials use different unit counts per square foot and different mortar ratios, so block and brick estimates are not interchangeable.

Bottom Line

Concrete block quantity depends on wall area, block face size, and mortar joint thickness, and a complete estimate also needs mortar, sand, and horizontal reinforcement. Enter your wall dimensions and block thickness above for an exact block count, and switch to Advanced mode to estimate grout fill and total material cost.

Browse Fix Supply's full assortment of concrete block and masonry supplies or contact our team for help selecting the right materials for your project.